T2s-usb-virtual-com-port-driver
CLICK HERE ->>> https://byltly.com/2ty8Og
```html
How to Install and Use the T2S USB Virtual COM Port Driver
The T2S USB Virtual COM Port Driver is a software that allows you to connect your T2S device to your computer via a USB cable and use it as a serial port. This can be useful for debugging, testing, or communicating with your device using serial commands.
In this article, we will show you how to install and use the T2S USB Virtual COM Port Driver on Windows 10.
Step 1: Download the Driver
You can download the driver from the official website of T2S: https://www.t2s.com/drivers/t2s-usb-virtual-com-port-driver.zip
Save the zip file to a convenient location on your computer and extract it. You should see a folder named \"T2S_USB_Virtual_COM_Port_Driver\" with two files inside: \"T2S_USB_VCP.inf\" and \"T2S_USB_VCP.cat\".
Step 2: Install the Driver
Before installing the driver, make sure your T2S device is disconnected from your computer. Then, follow these steps:
Open the Device Manager by pressing Windows + X and selecting Device Manager from the menu.
Click on the \"Action\" menu and select \"Add legacy hardware\".
Click on \"Next\" in the wizard that appears.
Select \"Install the hardware that I manually select from a list (Advanced)\" and click on \"Next\".
Select \"Ports (COM & LPT)\" and click on \"Next\".
Click on \"Have Disk\" and browse to the folder where you extracted the driver files.
Select \"T2S_USB_VCP.inf\" and click on \"Open\".
Click on \"OK\" and then on \"Next\".
If you see a warning message about installing unsigned drivers, click on \"Install this driver software anyway\".
Wait for the installation to complete and click on \"Finish\".
You have successfully installed the T2S USB Virtual COM Port Driver.
Step 3: Use the Driver
To use the driver, you need to connect your T2S device to your computer via a USB cable. Then, follow these steps:
Open the Device Manager again and look for a new device named \"T2S USB Virtual COM Port\" under the \"Ports (COM & LPT)\" category.
Note down the COM number assigned to the device (e.g., COM3).
Open a serial terminal program of your choice (e.g., PuTTY) and configure it to use the same COM number as your device, with a baud rate of 115200, 8 data bits, no parity, 1 stop bit, and no flow control.
Connect to the serial port and you should see a welcome message from your T2S device.
You can now send and receive serial commands to and from your device using the terminal program.
You have successfully used the T2S USB Virtual COM Port Driver.
```
```html
Step 4: Uninstall the Driver
If you want to uninstall the T2S USB Virtual COM Port Driver from your computer, you can follow these steps:
Disconnect your T2S device from your computer.
Open the Device Manager again and right-click on the \"T2S USB Virtual COM Port\" device under the \"Ports (COM & LPT)\" category.
Select \"Uninstall device\" from the menu.
Check the box that says \"Delete the driver software for this device\" and click on \"Uninstall\".
Wait for the uninstallation to complete and close the Device Manager.
You have successfully uninstalled the T2S USB Virtual COM Port Driver.
Conclusion
In this article, we have shown you how to install and use the T2S USB Virtual COM Port Driver on Windows 10. This driver allows you to connect your T2S device to your computer via a USB cable and use it as a serial port. You can use this feature for debugging, testing, or communicating with your device using serial commands. You can also uninstall the driver if you no longer need it.
We hope you found this article helpful and informative. If you have any questions or feedback, please feel free to contact us at support@t2s.com. Thank you for choosing T2S!
``` 061ffe29dd